Здравствуйте уважаемые заядлые форумчане и гости.
Приобрел сея агрегат и подключил через USB, принтер поднял согласно инструкции, но вот сканер...."некоторые запрошенные пакеты не могут быть установлены: kyodialog-0-0.x86_64(из-за неудовлетворенности cups-libs)"
Бродил по дремучим лесам, но ничего сделать не смог. Пытался установить sane-backends 1.0.27 и опять мимо. Помогите, а тож хочется на росе сея МФУ юзать, а не через винду. Кстати (для разработчиков): отсутствует kyocera в перечне принтеров, хотя сразу определяется системой, но драйвера не подставляет, в настройках принтера рекомендуемый драйвер "женерик" печатает черно белым
scanimage -L
[epsonds] unable to parse config line: net autodiscovery
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
sane-find-scanner tool
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
# Also you need support for SCSI Generic (sg) in your operating system.
# If using Linux, try "modprobe sg".
# No USB scanners found. If you expected something different, make sure that
# you have loaded a kernel driver for your USB host controller and have setup
# the USB system correctly. See man sane-usb for details.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
lsusb
Bus 001 Device 002: ID 0482:06b1 Kyocera Corp.
МФУ kyocera m5521cdn
lexa
Вернуться в «Обсуждение ROSA Fresh R4 - R8 (платформа 2014.1)»
Перейти
- Обсужденине ROSA Fresh R13 (альфа-версии на новой платформе)
- Обсуждение ROSA Fresh R12 (платформа 2021.1)
- РОСА с рабочей средой GNOME
- Обсуждение ROSA Fresh R9-R11.1 (платформа 2016.1)
- Сборки РОСЫ на базе LXDE, LXQT, MATE
- ↳ Fresh
- ↳ LXDE Marathon
- Общие вопросы по РОСЕ
- Программы РОСА десктоп
- Игры и Steam
- Сервер
- Информация от разработчиков
- ↳ Обсуждение сборочной среды ABF
- Роса wiki
- Важные события
- Работа форума
- English-speaking forums
- ↳ INSTALLATION
- ↳ Marathon (ROSA LTS)
- ↳ Desktop
- ↳ HARDWARE
- ↳ Marathon (ROSA LTS)
- ↳ Desktop
- ↳ ROSA Fresh R4-R7 (2014.1)
- ↳ Marathon (LTS) General Software
- ↳ ROSA Fresh R1-R3 (2012.1)
- ↳ Server
- ↳ Off the wall
- ↳ ROSA Fresh R9 and later (2016.1)
- ↳ ROSA Fresh R12 (2021.1)
- Localized Forums
- ↳ ROSA-Francophone
- ↳ Marathon (ROSA LTS)
- ↳ ROSA Desktop
- ↳ Conversations d'ordre général (ROSA&non-ROSA)
- ↳ ROSA-Italiano
- ↳ ROSA-Român
- ↳ ROSA-Español
- ↳ ROSA-Polska
- ↳ ROSA-Deutsch
- Архив
- ↳ Разговоры за жизнь, скорая психологическая помощь
- ↳ Курилка
- ↳ Обсуждение ROSA Fresh R4 - R8 (платформа 2014.1)
- ↳ РОСА Марафон (LTS)
- ↳ Обсуждение ROSA Fresh R2, R3 (платформа 2012.1)